MSD180 18HP 2WD Mini Tractor — ZS1105NM Single-Cylinder Diesel with Rear-Wheel Drive

The MSD180 belongs to the MSD series of small four-wheel agricultural tractors. It is a rear-wheel-drive, frame-chassis mini tractor built around the ZS1105NM single-cylinder diesel — a horizontal, water-cooled, direct-injection engine with a 105 mm bore, approximately 0.996 L displacement, and a 12-hour rated power of 12.1 kW / 2200 rpm. In the small-tractor trade this engine is commonly sold as an 18 hp-class unit. Compared with the 4WD MSD variants, the defining feature of the MSD180 is its 4×2 driveline: power goes to the rear axle only, which simplifies the machine, reduces weight and cost, and suits flat, firm ground where four-wheel drive would add complexity without adding much practical benefit. It is aimed at smallholders, orchardists, and greenhouse growers who want a low-cost, easy-to-maintain tractor for tillage, spraying, mowing, and light hauling.

Product Features & Advantages

ZS1105NM single-cylinder, direct-injection diesel. The 105 mm-bore, water-cooled ZS1105NM displaces approximately 0.996 L and carries a 12-hour rating of 12.1 kW at 2200 rpm (1-hour 13.3 kW) — an “18 hp-class” engine known for simple mechanical injection, easy starting, and field-serviceable reliability.

Simple 4×2 rear-wheel-drive layout. Without a front-drive axle or front driveshaft, the MSD180 has fewer components to wear, service, and replace. The result is lower purchase cost, lower maintenance cost, and a lighter machine that is easier to handle in confined spaces.

Tighter turning circle. The absence of a driven front axle allows a smaller turning radius than the 4WD MSD variants, which is an advantage in orchard rows, greenhouse aisles, and small yard manoeuvring.

6 forward + 1 reverse mechanical gearbox. The proven MSD shift pattern gives flexible speed selection for tillage, transport, and PTO work without electronic controls.

540 rpm PTO and category I three-point hitch. Industry-standard interfaces for rotary tillers, mowers, sprayers, and other small implements — no proprietary adapters required.

Differential lock for occasional low-traction moments. When one rear wheel loses grip on damp grass or loose soil, the differential lock ties the rear axle together and restores forward motion.

Water-cooled thermal stability. The ZS1105NM uses a condensing/radiator-type water-cooling system, supporting sustained PTO work and long working days better than air-cooled engines of similar output.

Product Technical Specifications

Engine data note: The ZS1105NM is listed with a 105 mm × 115 mm bore/stroke, ≈0.996 L displacement, 12-hour output 12.1 kW / 2200 rpm, and 1-hour output 13.3 kW / 2200 rpm. The “18 hp” designation reflects the 1-hour rating (13.3 kW ≈ 18.1 PS) and is the common trade label for this engine. Tractor-level dimensions and mass must be confirmed against the actual MSD180 factory specification; the 2WD layout typically gives a lighter operating weight and a smaller minimum turning radius than the equivalent 4WD MSD variant.

Product Usage Notes

Recognise the traction limits of a 2WD tractor. The MSD180 drives the rear axle only. On wet grass, loose soil, steep slopes, or with a heavily loaded trailer, rear-wheel drive will reach its grip limit sooner than a 4WD machine. Reduce the load, choose a lower gear, or postpone the job until ground conditions improve.

Add rear ballast for heavy draft work. When pulling a plough or a heavy tiller, rear wheel slip increases as draft load rises. Rear wheel weights or liquid ballast improve traction and reduce slip; follow the manufacturer’s ballast limits and tyre pressure recommendations.

Use the differential lock only as needed. Engage it when one rear wheel is slipping on damp grass or loose soil, and disengage it before turning on firm ground. Leaving it locked during normal steering loads the final drives and increases tyre scrub.

Respect PTO load limits, not just engine horsepower. The ZS1105NM is rated at 12.1 kW (12-hour) at the engine, but PTO output is lower. Compare the implement’s PTO power requirement against the tractor’s rated PTO power, not its engine rating.

Warm up the water-cooled diesel before load. Give the ZS1105NM a short low-idle warm-up, especially in cold weather, before running a PTO implement at full load.

Keep the cooling system clear. The ZS1105NM relies on water cooling; clean the radiator/condenser fins and check coolant level before each long session.

Check front-axle steering components and tyre pressure. The 2WD front axle carries steering and part of the machine weight. Check kingpins, tie rods, wheel bearings, and front tyre pressure regularly, and keep front and rear tyre pressures at the values specified for the load in use.

Labels / Markings

• Model: MSD180

• Engine model: ZS1105NM

• Engine power: 12.1 kW / 2200 rpm (12 h); 13.3 kW / 2200 rpm (1 h); 18 hp class

• Drive type: 4×2

• PTO speed: 540 rpm

• Transmission: 6F + 2R

• Hitch: Cat. I three-point

• Serial number / year of manufacture

• Manufacturer / importer information

• CE / applicable certification mark

Conclusion

If used properly, the Mingsin MSD180 mini tractor will become a reliable helper for the farmer. This equipment is striking in its efficiency, reliability and power!

Our Services:

Department Introduction of QC / Technical Support:

In order to get super quality, we have special QC department to control the product quality. This department is composed by experienced engineers who can offer us strong technical support easily. The engineers will inspect product quality both in order production and after order production to make sure each shipment we send to our customers is in the best status. With their strict quality control, our consistent quality wins us more and more orders from our international customers.

QC Flow:

1.Material inspection before production to avoid any potential problem from the very beginning.

2. Inspection for half-finished products during order production to find the problem earlier if any;

3. Inspection for finished products after production to make sure the products comply with customer's requirement.

Full Service and Product Warranty:

We offer our customers technical assistance and a full one year warranty on all products covering all manufacturing defects. ME Our manufacturing facility is completely computerized to provide our customers efficiency, reliability, high quality and timely shipments. Spare Parts:We can supply spare parts within 15 business days or sooner. Currently, part numbers are not available on-line. You may however determine the part number from your Parts Book or, if it is a simple part, you may describe the part and send us an order online. If you are not sure,please Contact Us .

Shipment: We can ship from our port in Qingdao or Shanghai, China to anywhere in the world within short days.

FAQ:

Q1: Are you a factory or trading company?

We have our factory for the farm machines and we also have our own trading company with self-supported import and export right.

Q2: How can I trust on your company?

We are a fully registered manufacture and exporting company by China Export Registration Authorities. Moreover, our products have been exporting to a number of countries including Switzerland, Russia, Spain, Netherlands, Australia, Peru, Thailand, Pakistan, Indonesia, Tanzania, Nigeria, South Africa, Sudan, Congo etc.

Q3: Where is your factory located? How can I visit there?

Our factory is located in Linyi City, Shandong Province, China. About 1 hour away from Linyi Airport, 4 hours away from Qingdao airport. All our clients are warmly welcomed to visit us!

Q4: How can I place an order from your website?

It is very easy.Once you find the implement you need on our website and place an inquiry against it, or, get to the inquiry section and leave us a message there with name, country and phone number, we will get in touch with you at the earliest.

Q5: How can I make the payment?

Payment is made via Telegraphic Transfer (T/T) through the bank against the proforma invoice.

30% as prepayment and the balance when the goods are ready for shipping.

Q6: What's the Payment terms?

T/T, L/C or some other ways payment method.

Q7: At which port do you usually ship the good?

We usually ship goods via Qingdao port of China.

Q8. How about the Warranty ?

12 months warranty from the time of the goods arrive at destination.